HP ATP FlexNetwork Solutions 認定 HP0-Y49 試験問題:
1. A network administrator needs to configure an IP address on VLAN 2 on an HP Cornware switch. The administrator enters these commands:
[Comvare]vlan 2
[Comware-vlan2] ip address 10.1.2.1 24
The CLI displays an error. What should the administrator do to configure the address correctly?
A) Use a "/" before the prefix length in the IP address command, ip address 10.1.2.1/24
B) Return to the system view and enable IP routing globally. Then enter the same VLAN2 and ip address commands again
C) Access the Layer 3 interface, interface vlan 2, and enter the ip address command there
D) Use a different prefix length in the IP address command. 24 Is an invalid length
2. A network administrator configures this command on an HP ProVision Switch: Vlan 30 ip helper-address 10.0.3.253
After the network administrator configures the command, using in VLAN 30 report that their PCs fail to acquire addresses using DHCP. Which command must the network administrator add to the ProVision switch configuration to solve this problem?
A) IP helper-address enable
B) IP routing
C) DHCP-relay
D) DHCP enable
3. Which command can a network administrator execute on an HP Cornware switch to manage configuration files?
A) Write memory
B) Write file
C) Delete
D) Startup-default
4. Refer to the Exhibit.
Exhibit: HP Comware switch configuration.
[Comware] vlan 100 [Comware-vlan100] quit [Comware] vlan 200 [Comware-vlan200] quit [Comware] interface g1/0/22 [Comware-GigabitEthernet1/0/22] port link-type trunk [Comware-GigabitEthernet1/0/22] port trunk permit vlan 100 200 [Comware-GigabitEthernet1/0/22] quit
A network administrator configures the Comware switch, as shown in the exhibit. The network administrator then connects a cable from the Comware's g1/0/22 interface to port 5 on an HP ProVision switch. Which configuration will successfully establish connection for VLAN 1, 100, and 200 between the two switches?
A) ProVision (config) # vlan 100 ProVision (config) # vlan 200 ProVision (config) # vlan 100 tagged 5 ProVision (config) # vlan 200 tagged 5
B) ProVision (config) # vlan 100 200 ProVision (config) # vlan 100 200 tagged 5
C) ProVision (config) # vlan 100 ProVision (config) # vlan 200 ProVision (config) # interface 5 tagged 100 ProVision (config) # interface 5 tagged 200
D) ProVision (config) # vlan 100 ProVision (config) # vlan 200 ProVision (config) # interface 5 tagged 100 200
5. Refer to the exhibits.
PC1 cannot reach PC2 Based on the exhibits, what could be causing this error?
A) PC 1 has the wrong IP address for its default gateway setting
B) Router A has a direct route, instead of a static route, to 10.1.10.0/24
C) The next hop address for the 10.1.20.0/24 route is incorrect
D) Router A has an invalid subnet mask for the VLAN 1 subnet
質問と回答：
| 質問 # 1 正解： A | 質問 # 2 正解： B | 質問 # 3 正解： D | 質問 # 4 正解： A | 質問 # 5 正解： A |
1088 お客様のコメント
品質保証JPexamはIT認定試験のシラバスに従って、試験問題の範囲を正確に絞って、的中率が99％の最新問題集を捧げます。
1年間の無料更新サービスJPexamは1年以内に問題集の無料更新サービスを提供し、お客様がいつでも最新版の問題集を持つことを保証いたします。もし試験の内容が変更されたら、弊社は直ちにお客様にお知らせします。それに、弊社の問題集が更新されたら、早速メールで最新バージョンを送付いたします。
全額返金JPexamの問題集を利用すると、短時間で勉強しても試験に合格できるのを保証いたします。試験に不合格になってしまった場合、弊社は全額返金いたします。(
ご購入前のお試しJPexamは問題集のサンプルを無料で提供いたします。ご購入前にサンプルを試用して製品の品質を確認することができます。ご遠慮なく利用してください。
