Avaya Ethernet Routing Switch Implementation 認定 6101.1 試験問題:
1. An engineer needs to assign an IP address of 172 25 10.31 for out of band management of an Ethernet Routing switch (ERS) 8600 switch a subnet mask of 255.255.255.192.
Which command line interface (CLI) command should the engineer use?
A) ERS8600:5# config bootconfig set ip 172.26.10 36/26
B) ERS8600:5# config bootconfig net mgmt ip 172.25.10.36/27
C) ERS8800:5 # config bootconfig set ip 172.25.10 36/27
D) ERS8600:5# config bootconfig net mgmt ip 172.25.10.36/26
2. After issuing a show mlt list stats (CLI) or show ist Stat (ACLI) command, it is determined that the running type is normal MLT and not 1ST
What are two causes of the IST not running properly? (Choose two)
A) The MLT ID does not match on both switches.
B) The IST is not enabled on both switches.
C) The peer IP address is not the address of the peer switch IST VLAN.
D) The peer IP addresses have to be 192.168.1.1/30 and 192.168.1.2/30.
3. A split multi link trunking (SMLT) for switch clustering is being configured.
Which statement is a configuration requirement for the SMLT?
A) Neighboring edge switch stacks should be connected to each other via DMLT connection to add resilient paths in the event of an SMLT failure
B) CP-limit is configured on edge switch stacks
C) VLANs that are defied on the SMLT are also defined on the MLT that defines the core IST
D) Alternate the primary path of the SMLT connection to load balance the switch core
4. Which statement describes how to configure Simple Loop Prevention protocol (SLPP) Rx?
A) SLPP is configured on the core switch cluster ports that connect to the edge switch.
B) SLPP is configured on the edge switch ports that connect to the core switch cluster.
C) SLPP is configured on the Inter Switch Trunk (1ST) ports of the core switch cluster.
D) SLPP is configured on the uplink ports of both the core switch cluster and the edge switch
5. Click on the exhibit button After checking the VLAN configuration using the show vlan info basic and the show vlan info port commands, there are no ACTIVE MEMBER ports for VLM4-50.
What is causing this problem?
A) The default setting for this type of VLAN is potential and no AppleTalk traffic has entered any of these ports
B) There are no devices connected to these ports.
C) AppleTalk Protocol VLANs do not have ACTIVE MEMBERS
D) The ports have not been configured as active for this VLAN
質問と回答：
| 質問 # 1 正解： D | 質問 # 2 正解： A、C | 質問 # 3 正解： C | 質問 # 4 正解： D | 質問 # 5 正解： A |
1024 お客様のコメント
品質保証JPexamはIT認定試験のシラバスに従って、試験問題の範囲を正確に絞って、的中率が99％の最新問題集を捧げます。
1年間の無料更新サービスJPexamは1年以内に問題集の無料更新サービスを提供し、お客様がいつでも最新版の問題集を持つことを保証いたします。もし試験の内容が変更されたら、弊社は直ちにお客様にお知らせします。それに、弊社の問題集が更新されたら、早速メールで最新バージョンを送付いたします。
全額返金JPexamの問題集を利用すると、短時間で勉強しても試験に合格できるのを保証いたします。試験に不合格になってしまった場合、弊社は全額返金いたします。(
ご購入前のお試しJPexamは問題集のサンプルを無料で提供いたします。ご購入前にサンプルを試用して製品の品質を確認することができます。ご遠慮なく利用してください。
